YASKAWA GA800 Series, Техническое описание

Страница: 944 / 1016

12.9 L: Protection Functions
944 YASKAWA SIEPC71061737B GA800 Drive Technical Reference
■
L8-19: Freq Reduction @ oH Pre-Alarm
No.
(Hex.)
Name Description
Default
(Range)
L8-19
(04BF)
Freq Reduction @ oH Pre-
Alarm
Sets the ratio at which the drive derates the frequency reference during an oH alarm.
0.8
(0.1 - 0.9)
When these two conditions are correct, this function is enabled:
• L8-03 = 4 [Overheat Pre-Alarm Ope Selection = Run@L8-19 Rate]
• oH alarm is output
■
L8-20: Control Fault & Step Out Detect
No.
(Hex.)
Name Description
Default
(Range)
L8-20
(04C0)
Expert
Control Fault & Step Out
Detect
Sets operation after the drive detects a CF fault when A1-02 = 4 [Control Method Selection =
Advanced Open Loop Vector] .
1
(0 - 2)
If you enter a Stop command but it cannot stop drive operation, the drive will detect CF .
0 : Disabled
1 : CF/STPo Detection Enabled
2 : CF ALM/Stop
The drive stops DC injection braking as specified by the value of b2-03 [DC Inject Braking Time at Start] .
Note:
• When A1-02 = 4 , control will not be stable if you do not do Rotational Auto-Tuning. This can cause CF faults if you ramp to stop. If the
drive detects CF , do Rotational Auto-Tuning and Line-to-Line Resistance Tuning. Also, do Line-to-Line Resistance Tuning.
•
If you set A1-02 = 4 and set these parameters, the drive can detect CF because it cannot stop the operation in some load conditions. Make
sure that you do Rotational Auto-Tuning and Line-to-Line Resistance Tuning correctly and then set L8-20 = 0 .
– d5-01 = 1 [Torque Control Selection = Torque Control]
–
L3-11 = 1 [Overvoltage Suppression Select = Enabled]
– Decreased L7-01 to L7-04 [Torque Limit] .
■
L8-27: Overcurrent Detection Gain
No.
(Hex.)
Name Description
Default
(Range)
L8-27
(04DD)
Overcurrent Detection Gain
Sets the PM motor overcurrent detection level as a percentage of the motor rated current value.
300.0%
(0.0 - 1000.0%)
Note:
• The overcurrent detection function detects the lower of these two values:
– Drive overcurrent level
–
Motor rated current × L8-27 / 100
•
Set L7-xx [Torque Limit] parameters < L8-27 .
• When you set L8-27 = 0.0 , it disables this function. In usual conditions, do not set L8-27 = 0.0 . If the drive rated current is much higher
than the motor rated current, PM motor magnets can demagnetize if current flows at the drive overcurrent detection level.
■
L8-29: Output Unbalance Detection Sel
No.
(Hex.)
Name Description
Default
(Range)
L8-29
(04DF)
Output Unbalance Detection
Sel
Sets the function to detect LF2 .
1
(0, 1)
This function prevents damage to PM motors. Current unbalance can heat a PM motor and demagnetize the magnets.
When the current is unbalanced, the drive will detect
LF2 to stop the motor and prevent damage to the motor.
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV