doble TDR9000 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 454

doble TDR9000 Скачать руководство пользователя страница 99

72A-1898 Rev. A 11/01

4-1

Monday

, November 26, 2001 1:09 pm

4. Setup and Operation

This chapter contains sections that discuss the following:

• Safety recommendations for use with the TDR9000
• Site preparation, including:

• Setting up the circuit breakers being tested
• Configuring the TDR9000 Test Plan
• Configuring TDR9000 connections

• Running a test

This chapter also discusses test safety recommendations, wiring, and
running First Trip/Close tests. Since First Trip tests require that the circuit
breaker be

energized

, references to discussions of test setup are found in

”First Trip/Close Tests”. Once test setup is complete, move to ”Using the
Pretest Checklist” on page 4-70 and proceed with the rest of the chapter
to run the test and disconnect after the test is complete.

First Trip/Close Tests

Specific discussions for First Trip/Close tests occur in the following
places:

• ”Safety Considerations: First Trip/Close Tests” on page 4-2
• ”First Trip/Close Virtual Front Panel Configuration” on page 4-2
• ”Configuring Analog/Auxiliary Channels for First Trip/Close Tests”

• ”Running a First Trip/Close Test: Special Considerations”

• ”Disconnecting After a First Trip/Close Test” on page 4-101

«
...
97
98
99
100
101
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов