doble TDR9000 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 454

doble TDR9000 Скачать руководство пользователя страница 131

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-33

Monday

, November 26, 2001 1:09 pm

N

OTE

It is possible to factory order an Event module configured for use with
24 V station batteries.

To connect an Auxiliary Contact:

1.

Attach one end of the Doble supplied Auxiliary Contact cable to a
pair of

Auxiliary Contact

channel banana jacks (

F

on Figure 4.13 on

N

OTE

The Auxiliary Contact measurement channels

are not

polarity sensitive.

2.

Taking appropriate safety precautions, use the attachment accessories
provided to attach the other end of the cable across the device to be
monitored, either directly across the device or at the terminal block.

Monitoring
Analog
Channels:
Current and
Voltage

The TDR9000 monitors both current and voltage using the Analog
Channel connectors of the Event module. The Event module analog
channels are used to accept:

• Voltage input (up to 300 V peak)
• Current probe input
• Current shunt input

Voltage Monitor

The Analog Channels accept voltage inputs up to 300 V peak.
Configuration is performed using the

Analog Channel Connector

or the

Analog Channels

dialog box of the Virtual Front Panel. Refer to

”Configuring the Event Module” on page 4-51.

N

OTE

The Analog cable is not symmetrical. The Instrument end has a shield
connector; the other end does not.

To connect a voltage input:

1.

Attach the Instrument end of the Doble supplied Analog cable to a
pair of Analog Channel banana jacks.

D

on Figure 4.13 on page 4-30.

N

OTE

Analog measurement channels

are

polarity sensitive.

2.

Make sure to attach the shield (green/yellow) banana plug to the
chassis ground (green/yellow) banana jack on the Event module.

Multiple shields can be stacked (see Figure 4.13 on page 4-30).

3.

Taking appropriate safety precautions, use the attachment accessories
provided to attach the other end of the cable across the device to be
monitored, either directly across the device or at the terminal block.

Generally, voltage measurements are made from the high side of the
load to the neutral rail.

«
...
129
130
131
132
133
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов