doble TDR9000 Скачать руководство пользователя страница 266 | Manualshive

Страница: 266 / 454

doble TDR9000 Скачать руководство пользователя страница 266

Test Plan Items

A-66

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Capacitance
Channel Parameters

The TDR9000 can measure the capacitance of grading capacitors that
are connected across the main contact of a circuit breaker in the range of
75 to 10,000 pF.

The test measures capacitance between each of the two EHV leads and
the common lead for each phase and each module. The test result is
presented as a pass/fail rating based on whether each measurement is
within the Test Plan limits.

Figure A.78 shows the parameters available for the Capacitance
channels.

Figure A.78 Capacitance Channel Activation

Parameters include:

Phase

This activates/deactivates on a phase-by-phase and
module-by-module basis.

Cap. Range

A scrollable picklist for selecting the Capacitor
configuration. Choices include:

• 75 - 2,5000 pF
• 300 - 10,000 pF

Capacitance Min.

A user-entered field for entering the minimum
expected capacitance.

Capacitance Max.

A user-entered field for entering the maximum
expected capacitance.

«
...
264
265
266
267
268
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов