manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 386 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 386

System Startup and Pre-Test Configuration

D-4

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

System Operation

The system is composed of two functional components, the Instrument 
and the controller software, TRXField, running on a laptop. The following 
describes the interaction between the two components.

System Startup and Pre-Test Configuration

On power up, the Instrument runs a short self-test to identify all cards and 
modules that are present. Once contacted by the controller, the 
Instrument transfers its configuration to the controller and it is displayed 
as a Virtual Front Panel on the computer's screen.

The channels of interest can be activated from the Virtual Front Panel or 
via a Test Plan created with the TRX or TRXField products. The type of 
test to perform is selected from a pull down menu on the Virtual Front 
Panel.

Test Execution

The controller downloads a list of channels to activate, range settings for 
the appropriate channels, and the signal on which to trigger the 
recording. Appropriate action by the operator (including the pressing of 
the Safety Switch) turns on all of the test voltages and starts the sampling 
of all the activated channels. Samples are stored in a circular buffer. 
When the predefined trigger signal is detected, the samples are 
transferred from the circular buffer to a permanent buffer pending the end 
of the test, at which point the information is transferred to the controller.

Data Transfer

The amount of data transferred to the controller is proportional to the 
number and type of channels activated. A Main Contact measurement 
could be made up of a channel of timing and a channel of pre-insertion 
resistance value measurement. Each Analog Channel and/or Auxiliary 
Contact channel is a single channel. The internal Trip and Close coil 
current channels are individual channels.

Data is compressed and transferred to the controller at 38.4 kbps. The 
different channel types compress to varying degrees depending on 
content: timing channels compress very well; analog channels do not.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов