doble TDR9000 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 454

doble TDR9000 Скачать руководство пользователя страница 109

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-11

Monday

, November 26, 2001 1:09 pm

Rotary/Linear Transducer Installation

The separate installation procedures for Dead Tank and Live Tank Circuit
Breaker transducer installations follow.

During both Dead Tank and Live Tank test setups, it is important to
perform connections in the following general order:

1.

Connect grounds

2.

Complete TDR9000 connections

3.

Complete connections to circuit breaker being tested

Additionally, before beginning transducer installation, make sure that the
circuit breaker is closed.

W

ARNING

When using a linear rod, make sure that the circuit breaker is in a

safe

position before beginning transducer installation. A safe position exists
when an accidental circuit breaker operation draws the rod into the
circuit breaker. This is usually the closed position.

Dead Tank Circuit Breaker

Since test voltages are below 48 V, it is important to provide good
connections between the Contact Monitoring cables and the bushings.

To install the transducer for a Dead Tank Circuit Breaker test:

1.

Determine the location for the transducer on the appropriate tank and
remove the circuit breaker top cap.

Figure 4.1 shows a typical mounting of the Rotary/Linear Transducer.

Figure 4.1 Rotary/Linear Transducer

«
...
107
108
109
110
111
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов