doble TDR9000 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 454

doble TDR9000 Скачать руководство пользователя страница 94

Trip/Close Module

3-24

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

When included with the TDR9000, the Trip/Close module normally
connects across the circuit breaker manual Trip or Close switch, as
shown in Figure 3.16.

Figure 3.16 Trip/Close Module Application

Trip/Close Current

The Trip/Close module can be outfitted with an optional internal current
measurement for the Trip and Close circuits. When this option is resident
on the system,

T/C Current

appears below the Trip/Close virtual

connector.

This option measures the Trip and Close circuit current during a
Trip/Close test by:

• Shunting the Trip and Close currents through the Trip/Close

Current component of the Trip/Close module

• Converting the measured voltage to a digital reading
• Sending the result to the Virtual Front Panel for display on the

Graphics

tab as a current waveform and on the

Tabulation

tab as

a peak current value

N

OTE

If the correct Close currents do not appear, refer to the
Doble Application Note: ”AN7: Monitoring Closing Coil Current with
the TDR9000™ Current Shunt in the Close Circuit” on page I-27
of this guide.

Trip/Close

Trip Coil

Auxiliary Contact

Station

Manual

Trip/Close

+

+ DC

Battery

Module

Current Option

Switch

«
...
92
93
94
95
96
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов