manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 116 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 116

Linear Transducer and Rotary Attachments

4-18

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

Rotary Motion

To configure for rotary motion:

1.

Remove the Rotary Chuck from its storage location on the Chuck 
Holder Plate by rotating it counterclockwise. 

The Chuck Key can be inserted into the Rotary Chuck for added 
torque.

2.

Remove the Chuck Holder Plate from the Transducer by loosening 
the two captive screws.

3.

Position the wrench portion of the Chuck Holder Plate on the Rotary 
Shaft (see Figure 4.6).

4.

Thread the Rotary Chuck onto the Rotary Shaft and hand tighten, 
using the Chuck Holder Plate to keep the Rotary Shaft from moving.

5.

Insert the Chuck Key into the Rotary Chuck. 

6.

Hold the Chuck Holder Plate against the Transducer and use a light 
object to tap the Chuck Key until it rotates the Rotary Chuck 
clockwise, tightening the Rotary Chuck on the Rotary Shaft.

7.

Remove the Chuck Key from the Rotary Chuck.

Figure 4.6  Chuck Holder Plate Mounting to Tighten Rotary Chuck

Version 1

Version 2

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов