manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 273 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 273

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

A-73

Monday

, November 26, 2001 1:09 pm

Main Contact 
Timing – Reclose

Parameters include:

Minimum

The minimum time from trip initiation to Main 
Contact make

Maximum

The maximum time from trip initiation to Main 
Contact make.

Figure A.85 shows how contact timing occurs on a module-by-module 
level.

Module (A)

The maximum allowable difference in time 
between the Trip initiation and the closing of the 
two Main Contacts in any module.

Phase (B)

The maximum allowable difference in time 
between the Trip initiation and the closing of any 
two Main Contacts in any phase.

Breaker (C)

The maximum allowable difference in time 
between the Trip initiation and the closing of any 
two Main Contacts in a circuit breaker.

Figure A.85  Main Contact Timing – Reclose

Module #1

Module #1

Module #2

Module #1

Module #2

Module #2

#!

#2

#3

#4

#!

#2

#3

#4

Contact #1

Contact #2

Contact #3

Contact #4

Main Contact reopening time

C

0

A

0

C

0

20

40

60

80

Time (ms)

First Switch to Last Switch

B

A

0

B

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов