doble TDR9000 Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 454

doble TDR9000 Скачать руководство пользователя страница 166

Configuring Test Plans

4-68

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

The following parameters are configured on the

Trigger Output

tab:

Trigger State

This picklist toggles the trigger output On or Off
and activates the other fields.

Pulse Width

A user-entered field that sets the pulse width of the
trigger out command in ms or cycles. This is the
length of time that the Trigger Output remains in
the active condition.

Polarity

Active Closed

only.

Trigger Delay

This user-entered field sets the length of time
between the start of the test and when the trigger
is set.

N

OTE

A negative time value for Trigger Delay causes the start of recording to
be delayed by that time value after the inception of the Trigger Out
command. A negative Trigger Delay can only be used when the Trigger
Source for the Trigger Input is set to None(Internal).

Time Display

Two radio buttons that toggle the time units
between ms and cycles.

When

OK

is clicked on the

Parameters

window, the

TDR9000

tab

reappears with the

Trigger Out

channel connectors activated.

«
...
164
165
166
167
168
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов