doble TDR9000 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 454

doble TDR9000 Скачать руководство пользователя страница 134

Connecting the TDR9000

™

Physical Front Panel

4-36

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Self-Zeroing Probe

The probe must be re-zeroed whenever a new Test Plan is loaded or a
channel is reactivated.

N

OTE

To conserve battery power, Doble’s MR 20 A/200 A/ 2 V Autozero
probe powers down after ten minutes. To disable this feature, when
turning the probe on, press the

Zero

button. The green LED flashes

several times to indicate the battery saver feature is disabled.

To zero the probe:

1.

Connect and zero the current probe by:

a. Taking appropriate safety precautions, plug the Instrument

end of the probe cable into the desired

Analog Channel

Connector

.

The

Analog

channel inputs are polarity sensitive.

Make sure to attach the shield (green/yellow) banana plug to
the chassis ground (green/yellow) banana jack on the Event
module.

b. Plug the free end of the

Analog

cable into the current probe.

c. Click the

Probe Zero

button on the Virtual Front Panel.

The following message displays on the Virtual Front Panel:

Adjust probe until tone becomes constant. The process will
end automatically when the probe is correctly adjusted for
2 seconds.

d. Turn the probe on by setting the selector switch to the desired

range.

N

OTE

Make sure that the probe is not attached to, or placed near,
current-carrying wires during the zeroing process.

e. Press the

Probe Zero

button on the probe.

When the probe reaches zero offset, the tone becomes steady.
If zero offset is maintained for two seconds, the tone stops and
the channel indicator turns green.

f. Repeat this procedure for any additional probes.

«
...
132
133
134
135
136
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов