doble TDR9000 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 454

doble TDR9000 Скачать руководство пользователя страница 181

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-83

Monday

, November 26, 2001 1:09 pm

Tabulation Tab

The Tabulation tab (Figure 4.59) is used to check measured values
against the manufacturer’s recommended limits. If the manufacturer’s
limits for the various measured parameters were entered in the Test Plan,
TRXField compares the measured vs. manufacturer’s limit and passes or
fails each parameter. If no limits were entered into the Test Plan, no
comparison can be made, but the measured values still appear.

This tab is useful when a user’s time or skill level does not permit a
detailed examination of a graphical display.

Figure 4.59 Tabulation Tab (Partial View)

Graphics Tab

The Graphics tab, using the

Overlay

function, gives a detailed

comparison between new Test Results and previous Test Results, as well
as between the results of different circuit breakers of identical types and
rating. Other tab features include

Zoom

and

Re-order

. The two cursors

are used to determine channel values at precise moments in time, for
example, to determine the time elapsed between two selected points, or
the distance between two selected points. TRXField shows the difference
between the primary (green) and secondary (red) cursor values by
subtracting green from red, and then showing the difference in yellow.

«
...
179
180
181
182
183
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов