doble TDR9000 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 454

doble TDR9000 Скачать руководство пользователя страница 91

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

3-21

Monday

, November 26, 2001 1:09 pm

Event

The Event module is split into two parts:

• Analog channels
• Auxiliary contact channels

Analog Channels

The analog part of the Event module has three general purpose analog
inputs for use in monitoring voltages or currents. These inputs are
individually configurable via the software to read inputs from current
shunts and probes, as well as voltages. Analog inputs are converted by a
high speed 12-bit analog-to-digital converter and then recorded at the
Instrument 10 kHz sample rate.

N

OTE

For applications where a current probe is used, a probe zeroing process
must be completed. Refer to ”Current Probes” on page 4-34.

Auxiliary Contact
Channels

The

Auxiliary Contact

portion of the Event module monitors the state of

up to three sets of auxiliary contacts.

These contact circuits ascertain whether a contact is:

• Open or closed
• If open, wet or dry, regardless of the polarity of the

excitation voltage

The TDR9000 has an automatic

wetting circuit

that wets a dry contact,

which allows the open/closed state of the circuit to be determined.

This module comes with three analog and three auxiliary contact
channels. For the present, this module can be used in Locations 1
through 5.

N

OTE

Ensure that the physical connections completed on the Physical Front
Panel reflect the numbering order of the Event module.

«
...
89
90
91
92
93
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов