doble TDR9000 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 454

doble TDR9000 Скачать руководство пользователя страница 54

2-4

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

TRX

™

and TRXField

™

Software

Figure 2.3 shows the working relationship between the TRX software
(with database components) and the TRXField software (control and data
collection), which is used to run tests. TRXField is included with the
TDR9000, and is also provided with the TRX installation.

Figure 2.3 TDR9000

™

System Information Flow Diagram

The features of both software programs are discussed below:

TRX

TRX is installed on an office computer or network
server that is responsible for data storage and
performing historical data analysis of circuit
breakers.

TRX offers the following features:

• The ability to design a library of circuit breaker

Test Plans from which an editable, circuit
breaker specific Test Plan can be created.

• The storage of test data.
• The evaluation of circuit breaker test data

from single and multiple tests and overlay
comparisons of Test Results from the same or
similar breakers.

The complete functionality of TRX software is explained in the

TRX User’s Guide.

Refer to ”TDR9000™ TRXField™ Software and Test

Plan Dynamics” on page A-28 for a discussion of the TRXField software
used to run the TDR9000.

Export from
Library of
Test Plans

Test Results

Run Tests

Import Results to Database

TRXField

TRX

• Library Test Plans
• Circuit Breaker Test Plans
• Test Result Storage
• Data Management

TRXField on laptop:

• Test Plan Edit/Create
• Run Test
• Tabular Results
• Graphical Viewer

TDR9000

• Control Processor

Import a Field Designed Test Plan for later use

• Firmware

Front Panel

TDR9000 Virtual

«
...
52
53
54
55
56
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов