doble TDR9000 Скачать руководство пользователя страница 73

Страница: 73 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

3-3

Monday

, November 26, 2001 1:09 pm

Table 3.1 describes the connections and switches present on the Physical
Front Panel. For the specifications of each channel, refer to ”TDR9000™
Circuit Breaker Test System Specifications” on page H-1.

OTE

Throughout this guide, “banana jack” refers to a banana jack connector
that is shrouded.

Table 3.1 TDR9000

™

Physical Front Panel Connections/Switches

Callout

Description

Circular 12-pin male connector for an OCB Contact Monitor cable

15-pin female connectors for Motion Transducer cables

Circular 12-pin male connectors for EHV Contact Monitor cables

Banana jack connectors for completing general purpose analog
measurements (voltage, current shunt and current probe inputs)

Banana jack connector for connecting the shield lead of analog test
cables to the chassis ground

Banana jack connectors for completing auxiliary contact timing
measurements

3-pronged male connector for use with an IEC standard power cord

Twist-Jack connector used to establish the system safety ground
through the ground cable

5-pin male connector for establishing Trip/Close control
connections

Trip and Close fuses

Banana jack connections for the Trigger In and Trigger Out
functions

9-pin female connector for the Doble supplied RS-232 serial
communications cable

Power ON/OFF switch/circuit breaker

4-pin male connector for the Doble-supplied Safety Switch cable or
Safety Bypass flag

DC power sources valid operation LED

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 73 / 454

Результаты поиска

Содержание TDR9000

Отзывы: