manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 436 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 436

Universal Adapter

I-26

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

The velocity trace displayed on the graphic output is the printout of the 
Average Velocity calculated as follows:

The position of the transducer rod at each 100 

µ

sec interval from the 

test initiation is recorded. From this data and the 100 

µ

sec time 

period, the individual Average Velocities are calculated. These 
Average Velocity points are then printed in the graphical output. The 
scale for the velocity is printed at the end of the graph.

The velocity that is tabulated is the highest Average Velocity calculated 
over the 100 

µ

sec intervals.

All velocity measurements are directly proportional to either linear or 
rotary movement of the circuit breaker. If the circuit breaker contact 
travel is not equal to the transducer rod travel, the Transfer Function 
provides the correction factor necessary for these measurements. These 
two values are entered by the user from data provided by the circuit 
breaker manufacturer and or the user; the default ratio is 1.00 to 1.00. 

Displacement values near the beginning or end of travel should be 
avoided.

During a Trip test the circuit breaker remains closed for several 
milliseconds after the Trip signal is applied. If zero displacement is 
selected as the beginning of the zone, the TDR9000 starts timing at test 
inception and the several milliseconds that the breaker remains fully 
closed prior to circuit breaker movement are included in the time used 
for the calculation of Average Velocity for the specified zone.

For Close tests, zero is also the fully closed position of the circuit breaker. 
If zero is chosen as the end point and the circuit breaker mechanism 
continues to move for the majority of the Close test, due to the dampener, 
the time used for the Average Velocity will again be excessively long.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов