doble TDR9000 Скачать руководство пользователя страница 66

Страница: 66 / 454

Trip Free (C-O)

2-16

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Trip Free (C-O)

Figure 2.11 is a simplified representation of the test waveform generated
for the Trip Free test.

Figure 2.11 Trip Free Command Pulse

Command
Parameters

Close Pulse

This time setting determines the duration of the
Close Pulse sent to operate the close circuit of the
circuit breaker.

Trip Free and Delay

These parameters determine when the Trip Pulse is
initiated:

Standing

Initiates .5 cycles (8.3 ms at 60 Hz) after the test
starts.

Delay

Initiates after the time entered in the

Delay Length

field.

Contact

Make

Initiates when the TDR9000 senses that a contact
make has occurred on the first of the Main
Contacts.

Recording Length

This setting determines the recording length and
implicitly sets the sampling rate at which the
recording is performed.

133 msecs

Trip Command
Close Command

Delay

Off

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 66 / 454

Результаты поиска

Содержание TDR9000

Отзывы: