doble TDR9000 Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 454

doble TDR9000 Скачать руководство пользователя страница 191

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-93

Monday

, November 26, 2001 1:09 pm

Use phase encoded signal colors

Enables the automatic encoding of phases in the
display, as shown in Table 4.10.

If more than four Test Results are displayed, this
feature automatically turns off. The result is that all
channels from a given circuit breaker become the
same color. It is assumed that with five or more
circuit breakers, a comparison of channels among
different circuit breakers is more necessary than a
comparison of different channels associated with
the same circuit breaker.

Automatically overlay signals with the same name

Overlays similar channels automatically.

Table 4.10 Phase Encoded Signal Colors

Test Result In Frame

Phase

Color

First

Phase A

Red

Phase B

Yellow

Phase C

Blue

Second

Phase A

Purple Bright

Phase B

Green

Phase C

Bright Light Blue

Third

Phase A

Brown

Phase B

Olive Green

Phase C

Purple Medium Dark

Fourth

Phase A

Black

Phase B

Green Flat

Phase C

Blue Flat

«
...
189
190
191
192
193
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов