manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 350 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 350

Physical Front Panel Modules

B-22

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

Table B.3 lists the replaceable internal boards and their part numbers.

Physical Front Panel Modules

The following Front Panel modules can be replaced in the field:

• OCB/Motion
• EHV
• Event

These replacement procedures are geared to replacing only Front Panel 
modules that have failed in existing configurations. Reconfiguration of 
the TDR9000, changing the type of module located in any position, must 
be done by Doble personnel.

N

OTE

The System Front Panel module is not replaceable in the field. If 
troubleshooting analysis indicates a problem or failure is related to this 
module, contact Doble Customer Service. Also, it is necessary to 
remove the module in Location 2 before removing a module in 
Location 1.

Table B.3  Replaceable Internal Board Part Numbers

Circuit Board

Part Number

EVG

04S-0691-01

CPU

04D-0603-04

Event (3A/3X)

04S-0694-01

Trip/Close Module

03D-1372-01 (with Trip/Close Current)
03D-1372-02 (without Trip/Close 
Current)

Main Contact Master

04S-0692-01 (with resistance)
04S-0692-02 (without resistance)

Main Contact Slave

04S-0692-03 (with resistance)
04S-0692-04 (without resistance)

Capacitance Measurement 
Board

04S-0695-01

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов