manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 69 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 69

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

2-19

Monday

, November 26, 2001 1:09 pm

Self-Diagnostics

The Self-Diagnostics test performs a two-tiered analysis of machine 
functionality. This test determines the validity of both the Physical Front 
Panel and the internal operations based on the results from the 
processing of pre-determined signals. These signals are designed to 
emulate the signal flow that occurs on all measurement channels during 
various tests. Refer to ”Self-Diagnostics Test” on page B-1.

First Trip/Close Tests

Use a First Trip/Close to capture operational data for circuit breakers that 
have been idle. To preserve the integrity of data, and to study the 
characteristics of long dormant circuit breakers, these tests are performed 
on circuit breakers without removing them from operation. Main Contact 
timing test results appear as waveforms instead of the usual contact state, 
trip, resistor level/bounce, and close, because a CT secondary is used as 
the signal source instead of the main contact cables, since the Main 
Contacts are energized. 

N

OTE

• Compare the First Trip/Close Test Results with subsequent operations 

of the same type.

• These tests are useful for long idle spare breakers as well.

First Trip/Close Test 
Measurements

The TDR9000 can be used for First Trip/Close testing on IPO circuit 
breakers as well as those with a single mechanism for the three phases. 
Any number of signals are measurable, including motion and velocity. A 
First Trip/Close Test Plan can be designed to quickly test a distribution 
breaker of relatively low system importance, while another may include 
a complete set of tests on a circuit breaker that is rarely removed from 
service. The former requires a Test Plan designed for quick testing and a 
minimum set of channels, while the latter setup requires a recommended 
set of channels. In this guide, the process is described using an external 
trigger. After the first Trip test, a Close test should also be run followed by 
a second Trip and Close test for comparison purposes.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов