manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 3 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 3

Warranty

Equipment Limited 
Warranty

Doble Engineering Company (DOBLE) warrants the products that it 
manufactures to be free from defects in material and workmanship for a 
period of one year from the date shipped from the factory.

During the one year warranty period, DOBLE will repair or replace, at its 
option, any defective products or components thereof at no additional 
charge, provided that the product or component is returned, shipping 
prepaid, to DOBLE. The Purchaser is responsible for insuring any product 
or component so returned and assumes the risk of loss during shipment. 
All replaced products and components become the property of DOBLE.

THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCTS 
WHICH HAVE BEEN DAMAGED AS A RESULT OF ACCIDENT, MISUSE, 
ABUSE, OR AS A RESULT OF MODIFICATION BY ANYONE OTHER 
THAN DOBLE OR AN AUTHORIZED DOBLE REPRESENTATIVE.

EXCEPT AS EXPRESSLY SET FORTH ABOVE, NO OTHER WARRANTIES, 
EXPRESSED OR IMPLIED, ARE MADE WITH RESPECT TO THE 
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE. DOBLE EXPRESSLY DISCLAIMS ALL 
WARRANTIES NOT STATED HEREIN. IN THE EVENT THE PRODUCT IS 
NOT FREE FROM DEFECTS AS WARRANTED ABOVE, THE 
PURCHASER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT AS 
PROVIDED ABOVE. UNDER NO CIRCUMSTANCES WILL DOBLE BE 
LIABLE TO THE PURCHASER OR ANY USER FOR ANY DAMAGES, 
INCLUDING WITHOUT LIMITATION, PERSONAL INJURY OR 
PROPERTY DAMAGE CAUSE BY THE PRODUCT, ANY INCIDENTAL 
OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST 
SAVINGS, OR OTHER DAMAGES ARISING OUT OF THE USE OF OR 
INABILITY TO USE THIS PRODUCT.

Software Limited 
Warranty

THIS SOFTWARE PRODUCT IS PROVIDED “AS IS” WITHOUT 
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, 
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE 
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THIS 
SOFTWARE PRODUCT IS WITH PURCHASER SHOULD THE 
PRODUCT PROVE DEFECTIVE. PURCHASER (AND NOT DOBLE OR 
AN AUTHORIZED DEALER) ASSUMES THE ENTIRE COST OF ALL 
NECESSARY SERVICING, REPAIR, OR CORRECTION.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов