manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 260 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 260

Test Plan Items

A-60

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

The rotary to linear Transfer Function is used when the manufacturer 
provides specification for the linear motion of the contacts, however, the 
mechanism accessible for the transducer connection is involved in a 
rotary motion (Figure A.72). The rotary to linear Transfer Function is also 
checked for the entry of a ratio that is too large.

Figure A.72  Transducer Wheel

The default value for a rotary to linear Transfer Function using English 
transducer units is 1.00 in/50.00 deg.

The following is an explanation for the chosen default value.

The transducer wheel has a circumference of 5". Consequently, if the 
Main Contact travel is such that the transducer wheel makes a full turn 
(360 deg.), the rod pressing against the wheel would have moved 5".

If the transducer rod movement is the result of the wheel movement of 
1 deg., the transducer rod traveled:

1 deg./360 deg. x 5" = 0.01389"

If the default Transfer Function value is 1"/1 deg., which seems logical, 
the Transfer Function ratio is:

1"/0.01389" = 72, which is above the 50 that the Instrument uses as a 
limit.

To bring the Transfer Function ratio into the more practical (and 
allowable by the Instrument) range, the Instrument defaults to the 
1"/50 deg., which results in the following ratio:

50 deg./360 deg. x 5" = 0.694", 1"/0.694" = 1.44

360°

5°

Main 

Code
Wheel

Contact

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов