doble TDR9000 Скачать руководство пользователя страница 357 | Manualshive

Страница: 357 / 454

doble TDR9000 Скачать руководство пользователя страница 357

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

B-29

Monday

, November 26, 2001 1:09 pm

W

ARNING

All the cables used for this test should be detached from the breaker
while performing this procedure.

Example

Connect a Trip clip to a contact clamp, connect a Close clip to
another contact clamp, and connect the remaining Trip/Close clips to
the common clamp.

2.

Run a test sequence that exercises both controls (e.g., Trip Free,
Reclose, O-C-O).

3.

Check for activity on both contact channels.

• If only one control is misbehaving, the test can be done using

only one contact channel and the suspect T/C clip pair. Run a
simple test (e.g., Trip, Close).

• If both the Trip and Close control pulses are seen on the contact

channels graphs, the TDR9000 is OK. The problem is outside the
Instrument.

• If one or both of the patterns is missing, check the fuses with a

meter.
• If the fuses are OK, then the cable is suspect.
• If the fuses and cables are OK, then replace the Trip/Close

module. Refer to ”Internal Circuit Boards” on page B-19.

• Otherwise, replace the bad fuse. Refer to ”Replacing

Trip/Close Fuses”.

Replacing
Trip/Close Fuses

To replace fuses:

1.

Turn the power OFF.

2.

Remove and replace the defective fuse using a flat head screwdriver.

W

ARNING

Always use a bus type 3 A, 250V Slo-Blo (Doble Part # 384-0002). Use
of any fuse other than the designated type can result in damage to the
TDR9000.

3.

Restore system connections.

4.

Turn the power ON.

«
...
355
356
357
358
359
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов