doble TDR9000 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 454

doble TDR9000 Скачать руководство пользователя страница 63

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

2-13

Monday

, November 26, 2001 1:09 pm

Trip (O)

Figure 2.8 shows a simplified version of the test waveform generated for
the Trip/First Trip test.

Figure 2.8 Trip Command Pulse

Command
Parameter

Trip Pulse

This time setting determines the duration of the
Trip Pulse sent to operate the trip circuit of the
circuit breaker.

Recording Length

This setting determines the recording length and
implicitly sets the sampling rate at which recording
is performed.

Table 2.2 Circuit Breaker Test Types

Test

Initial State

Intermediate

Final State

State 1

State 2

Trip (O)/First Trip (O)

Closed

—

—

Open

Close (C)/First Close (C)

Open

—

—

Closed

Reclose (O-C)

Closed

Open

Closed

Trip Free (C-O)

Open

Closed

—

Open

O-C-O

Closed

Open

Closed

Open

Slow Close (C)

Open

—

—

Closed

Continuity

This test checks the continuity of contact connections. The circuit
breaker is not operated.

Capacitance

This test checks the capacitance characteristics of the grading
capacitors connected across the Main Contact of a circuit breaker.
The circuit breaker must be open, but is not operated during the test.

Self-Diag.

This test checks Instrument measurement channel operation by
performing test emulations. The circuit breaker does not operate.

66 msec

On

Off

«
...
61
62
63
64
65
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов