doble TDR9000 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 454

doble TDR9000 Скачать руководство пользователя страница 80

Connector Indications

3-10

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

B

Indicates that the firmware has confirmed that a
measurement channel has been detected, and that
it is ready for use. This means that all connections
that can be detected (transducers and certain
cables) have been made and that all operations
required prior to a test, such as probe zeroing, have
been completed. For this component:

• Red indicates the channel is not ready for use.
• Green indicates the channel is ready for use.
• If all the connectors on the Virtual Front Panel

have a gray center, there is no communication
between the Instrument and the laptop via the
serial port.
• Check the serial port connections.

• Component B is gray when:

• Channels are activated in the Test Plan, but

there is no communication with the
TDR9000.

• There is communication with the

TDR9000, but channels are activated for a
module that is not physically present in the
instrument. Modules not present on the
Virtual Front Panel appear gray.

N

OTE

The entire Virtual Front Panel, except for the System module, is gray if
there is no communication with the TDR9000 and there are no
channels activated in the Test Plan.
If the Instrument does not support the current Test Plan, the channels
not supported must be de-activated via the Test Plan or TDR9000 tab.

«
...
78
79
80
81
82
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов