manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 251 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 251

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

A-51

Monday

, November 26, 2001 1:09 pm

Trigger Input 
Parameters

This feature enables the user to operate a circuit breaker using an 
external trigger, such as a command from a remote control room, instead 
of the Run Test button.

There are three Trigger Source conditions:

None (Internal) 

Test recording is triggered internally, and accepts 
no external trigger inputs. The Instrument controls 
the circuit breaker using the Trip/Close module. 

AUX Contact 

An input that comes in through an Auxiliary 
Contact triggers the test and is assigned to be 
recorded on a designated channel of the Event 
module (Figure A.63). The Trip/Close module is not 
used for this test. The trigger can be one of four 
types:

• Open to Close
• Close to Open
• Volts On to Volts Off
• Volts Off to Volts On

Figure A.63  AUX Contact Trigger Parameters

N

OTE

The AUX Contact Trigger In channel is designed to work in a substation 
using station battery voltages of 48 VDC or higher. Voltages less than 
48 VDC may not meet the threshold requirements of the Volts On state.

After selecting the type of trigger, the TDR9000 channel being used to 
monitor this trigger must be specified. Fifteen channels are available 
(optionally) on the TDR9000: 1 through 5, C1 through C3. To record the 
timing of the channel receiving the trigger, activate this chosen channel 
(see ”Auxiliary Contacts Channel Activation” on page A-67).

”Pre-Triggering Data Collection” on page A-53 describes the pre-trigger 
data functionality available for this test.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов