doble TDR9000 Скачать руководство пользователя страница 361 | Manualshive

Страница: 361 / 454

doble TDR9000 Скачать руководство пользователя страница 361

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

B-33

Monday

, November 26, 2001 1:09 pm

Safe Packing of the
TDR9000

™

If troubleshooting and the completion of Doble requested parts
replacements fails to resolve a system problem, the TDR9000 may need
to be sent back to Doble for servicing. It is recommended that the
original packing material be kept for reuse. Before transporting, contact
Doble Engineering Customer Service at 617-926-4900 or FAX
617-926-0528, for return instructions.

Before packing:

1.

Disconnect and remove all external cables.

2.

Attach the front cover.

If the original packing material is not available, pack the Instrument for
shipment as normal for fragile, electronic equipment. Alternatively, triple
wall shipping containers can be ordered from Customer Service for a
nominal charge (Doble Part # 903-0044). The Instrument may be packed
using either of the following methods:

• 2-wall minimum corrugated cardboard box with a minimum 2

inch thick poly foam padding.

• Wood crate with minimum of 2 inch thick poly foam padding all

around.

N

OTE

Doble Engineering is not responsible for shipping damage. Carefully
protect each Instrument from shipping and handling hazards. Ensure
protective covers are securely in place.

Instruments must be sent to Doble freight pre-paid, unless other
arrangements have been authorized in advance by Doble Customer
Service.

Before returning the Instrument to Doble Engineering, contact
Customer Service to obtain a

Repair Work Order (RWO)

number. The

RWO number must be attached to the Instrument, as it is used to track
the Instrument during shipping to Doble and back to the customer.

Instruction manuals, cables, and transducer connecting rods should not
be returned with an Instrument, unless recommended by Doble
Customer Service.

«
...
359
360
361
362
363
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов