doble TDR9000 Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 454

doble TDR9000 Скачать руководство пользователя страница 188

Working with Test Results

4-90

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

To change the order in which the channels appear:

1.

Use the

Open

icon or select

File/Open

to open a Test Result.

2.

Click the

Drag and Drop

icon next to the channel to be moved.

3.

Drag the mouse to the new location for that channel.

The

Re-order

appears.

4.

Release the mouse button.

N

OTE

If the Overlay icon appears and the mouse button is released by
mistake, the channel is overlaid, rather than re-ordered.

To restore the entire Test Result:

• Click the

Reload Original

button.

Cursors

TRXField has a primary (green) and a secondary (red) cursor, or vertical
marker, which is used to determine either the value of a channel or the
time elapsed at one or more chosen points.

The time appears in the bottom right corner of the data screen. The
channel values appear to the right of each channel.

Facts about cursors include:

• Precisely positioning the cursors determines the time and distance

values for a channel which can then be compared to the
manufacturer’s specifications.

• If the primary cursor (green) appears, the time and values are

displayed in green.

• If both the primary and secondary cursors appear, the times and

channel values at each cursor point appear. These values appear
in their respective colors (green and red), with the delta value for
time in yellow, along the right side of the

Data

window.

To activate the cursors:

1.

Activate the primary (green) cursor first.

Position the mouse at or near the point of interest on the channel.

2.

Click the mouse and the green cursor appears, along with the cursor

Delete

button (green).

3.

Reposition the cursor by clicking the mouse repeatedly.

«
...
186
187
188
189
190
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов