manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 437 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 437

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

I-27

Monday

, November 26, 2001 1:09 pm

AN7: Monitoring Closing Coil Current with the 
TDR9000

™

Current Shunt in the Close Circuit

The TDR9000 system uses one set of control leads to control the 
operation of the circuit breaker and to monitor the Trip or Close current.

N

OTE

The TDR9000 close current measurement can handle a maximum of 
20 A.

Previous test sets used a relay to initiate the Trip or Close operation. Since 
the pickup time of the initial relay varies from test to test, a method to 
mark the time of test initiation was necessary. A second set of leads 
(sense channel) provided this function and enabled timing from that 
reference point on the trace. Since the TDR9000 uses its solid-state 
control circuitry to initiate operational tests, this sense circuit is not 
necessary. The Trip and Close circuits of the TDR9000 incorporate 
optional shunts that enable the instrument to monitor and measure Trip 
and Close currents.

Since most Close tests are initiated with the Close leads bridging a 
closing contact on a control switch or a push button, the current 
monitored is the current that is present in the 

X

 relay circuit rather than 

the Closing Coil circuit.

The current in the Close coil circuit can be monitored and measured if a 
few temporary clip-to-clip jumpers are added (Figure I.23).

Figure I.23  Jumper Placement

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов