doble TDR9000 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 454

doble TDR9000 Скачать руководство пользователя страница 76

Tab Navigation

3-6

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

The Test Plan and TDR9000 tabs are used to configure Test Plans as
follows:

Test Plan

All data can be configured here. This includes
channel activation and the input of the
performance specifications. The data fields present
on this tab are fully explained in Appendix A
”TRXField™ Software and Circuit Breaker Testing
Theory”.

TDR9000

This tab contains the Virtual Front Panel. Channel
activation and labeling can be set. Refer to ”Setting
Up a Test Plan Manually with TRXField™”
on page 4-43 for configuration information.

The Edit Specs., Tabulation and Graphics tabs are used to work with Test
Results as follows:

Edit Specs.

This tab displays all of the parameters that were
configured when the test was run. Some of these
fields are active and editable. When these fields
are edited, the data displayed on the Tabulation
and Graphics tabs change to reflect the effect new
parameter settings have on the data gathered
during the test. This is a useful way in which to
study and compare data on circuit breaker
operations.

N

OTE

The Edit Specs. functionality does not change the specifications in the
original Test Plan, nor does it change the actual data gathered during
that test.

Tabulation

Tabular Test Results are viewed on this tab.

Graphics

Graphical Test Results are viewed on this tab.
The presentation characteristics of the results are
tailored, using the operations explained in
”Working with Test Results” on page 4-81.

The contents of the

Test

Plan

,

Tabulation

and

Graphics

tabs are printable

using the optional printer, or any other connected printer.

N

OTE

TRXField also supports a functionality that displays multiple Test Results
together on a Graphics Overlay tab. This function is performed using
the Overlay Graphics selection of the File menu.

«
...
74
75
76
77
78
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов