doble TDR9000 Скачать руководство пользователя страница 141

Страница: 141 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-43

Monday

, November 26, 2001 1:09 pm

Setting Up a Test
Plan Manually with
TRXField

™

Once the choice to manually create a Test Plan is made, the

New Test

Plan - TRXField

window (Figure 4.19) appears (Only the top portion of

this window is shown). All the data fields required to create a Test Plan
appear on this

Test Plan

editor tab. Explanations of all these fields are

given in Appendix A ”TRXField™ Software and Circuit Breaker Testing
Theory”

Figure 4.19 is primarily meant to show the two tabs that appear at this
time on TRXField:

Test Plan

and

TDR9000

OTE

The Test Plan tab is the default tab. It is not possible to move to any
other tab until the Model Number is entered.

Figure 4.19 TRXField

™

Library Test Plan

The

Test Plan

and

TDR9000

tabs are used to configure Test Plans. Since

Appendix A ”TRXField™ Software and Circuit Breaker Testing Theory”
explains the use of the fields on the

Test Plan

tab, the discussions in this

chapter focus only on the use of the

TDR9000

tab Virtual Front Panel to

create or modify Test Plans. All changes implemented on the Virtual
Front Panel are reflected on the

Test

Plan

tab.

OTE

Not all parameters available on the Test Plan tab are available on the
TDR9000 tab.

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 141 / 454

Результаты поиска

Содержание TDR9000

Отзывы: