doble TDR9000 Скачать руководство пользователя страница 329 | Manualshive

Страница: 329 / 454

doble TDR9000 Скачать руководство пользователя страница 329

72A-1898 Rev. A 11/01

B-1

Monday

, November 26, 2001 1:09 pm

Appendix B. Troubleshooting and Parts
Replacement

This appendix covers troubleshooting for the TDR9000 and related parts
replacement procedures.

Troubleshooting

The topics that follow discuss these troubleshooting-related areas:

• Running and interpreting the results of the Self-Diagnostics test
• Analyzing the system for specific problems
• Troubleshooting tools designed to pinpoint problems based on

symptoms, including:
• Troubleshooting flowcharts
• A Problem/Solution table
• A drawing, from the top view, of the circuit boards that

comprise the system

• Interpreting TDR9000 LEDs

Self-Diagnostics Test

The Self-Diagnostics test is comprised of the two different automated test
sequences defined below. For both tests, all external stimuli are
physically disconnected from the inputs using relays that switch
simulated test signals into each of the sensor channels.

Global Self Test

This test always runs and if it detects no failures,
completes the Self-Diagnostics cycle. It sources test
signals to the Physical Front Panel. Isolation of the
Physical Front Panel is achieved by breaking the
input circuit just inside the front panel connector.

«
...
327
328
329
330
331
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов