doble TDR9000 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 454

doble TDR9000 Скачать руководство пользователя страница 101

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-3

Monday

, November 26, 2001 1:09 pm

• In the Command Parameters on the Virtual Front Panel, select the:

Trigger source:

• Aux Contact if using an Auxiliary Contact channel on the

Event module

• Trigger In if the TDR9000 System module has the Triggers

option

Trigger event:

• Close
• Open

The trigger event is the change of state the TDR9000 is expecting
to see before recording the test data. During a First Trip Test, the
closing of the 52CS/T contacts initiates the recording. During a
First Close Test, the closing of the 52CS/C contacts initiates
recording.

• If using the “Aux Contact” trigger source, select the trigger

channel where the trigger signal is received. Select the pre-trigger
time, or leave it at the default, zero (see page 4-65).

• For each relay contact state measured, an Auxiliary Contact

channel must be activated, given a label and a phase. If the relay
contact state is measured using a Trigger In channel (the Triggers
option must be present on the System panel), there is no need to
activate an Auxiliary Contact channel for it. Activate only the
channels being used. When performing a First Close test, both the
52CS/T label in the Test Plan must be changed to 52CS/C and the
cables must be transferred, since this contact is being used to
trigger the Close operation.

• For each current or voltage waveform to be measured, an Analog

Channel must be activated, given a label and a phase. All Analog
currents are measured using Doble probes, except for the DC
supply voltage. Activate only the channels being used. When
performing a First Close test, the Trip Coil label must be changed
to Close Coil.

• If Motion transducers are permanently installed, the motion

channels must be activated, and a label and phase selected.

«
...
99
100
101
102
103
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов