doble TDR9000 Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 454

doble TDR9000 Скачать руководство пользователя страница 163

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-65

Monday

, November 26, 2001 1:09 pm

•

Trigger In

trigger

This is when the trigger comes in through the
Trigger In connectors of the System module.
This selection automatically activates the
channel for recording.

Timing Event

This picklist is used to select the change in contact
status that causes the trigger and initiates data
recording. Choices available depend on the

Trigger

Source

and are outlined in Table 4.7.

Trigger Channel

This picklist is used to select the channel
configured to accept the trigger input. It is only
active when

AUX

Contact

is in use for the

Trigger

Source

. The number of channels available depends

on the number of Event modules in the TDR9000.

Pre-Trigger

This user-entered field sets the length of time, in ms
or cycles, prior to a triggering event for which data
is retrieved from the circular buffer. The TDR9000
is able to do this because it continually records
data once the Continue button is clicked for an
external trigger test. The pre-trigger time is
subtracted from the total recording time; the
overall recording time does not change.

Time Display

These two radio buttons toggle the time units
between ms and cycles.

Table 4.7 Trigger Input Timing Events

Trigger Source

Timing Events Available

AUX Contact

• Open to Close
• Close to Open
• Volts On to Off
• Volts Off to On

Trigger In

• O

→

C or On

→

Off

(Open to Close or Volts On to Volts Off)

• C

→

O or Off

→

On

(Close to Open or Volts Off to Volts On)

«
...
161
162
163
164
165
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов