doble TDR9000 Скачать руководство пользователя страница 30

Страница: 30 / 454

Step 1: Circuit Breaker Preparation

1-4

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Figure 1.1 Step 1: Circuit Breaker Control Cabinet Preparation

Circuit Breaker
Connections:
First Trip/Close Test

The connections to the breaker are outlined in the steps below:

OTE

Once this is complete skip to ”Step 4: Laptop and TDR9000™ Test Plan
Configuration” on page 1-15.

Connect the TDR9000 ground connection to circuit breaker ground.

Connect a Doble current probe to a CT secondary for each phase
being measured, to record the Main Contact currents.

Connect Doble current probes to selected relay coil circuits and then
to TDR9000 event module.

Connect a set of Analog cables across the DC supply switch to
monitor the DC bus voltage. Set up the channel for voltage sense and
range.

Connect Auxiliary Contact cables across the selected contact and
connect to an Aux contact.

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 30 / 454

Результаты поиска

Содержание TDR9000

Отзывы: