doble TDR9000 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 454

doble TDR9000 Скачать руководство пользователя страница 61

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

2-11

Monday

, November 26, 2001 1:09 pm

TDR9000

™

Physical Front Panel Configurations Supported

Table 2.1 lists the configurations possible for the Physical Front Panel.
Some configurations require that different boards be used in the
backplane slots.

Table 2.1 Physical Front Panel Configurations

Location 1

Location 2

Location 3

Location 4

Location 5

Location 6

Motion/OCB or Empty

Empty

Empty

Empty

Empty

System

Motion/OCB or Empty

EHV 1-2

Empty

Empty

Empty

System

Motion/OCB or Empty

EHV 1-2

EHV 3-4

Empty

Empty

System

Motion/OCB or Empty

EHV 1-2

EHV 3-4

EHV 5-6

Empty

System

Motion/OCB or Empty

EHV 1-2

EHV 3-4

EHV 5-6

EHV 7-8

System

Motion/OCB or Event

EHV 1-2

EHV 3-4

EHV 5-6

EHV 7-8

System

Motion/OCB or Empty

Empty

Empty

Empty

Event 5

System

Motion/OCB or Empty

Empty

Empty

Event 4-6

Event 5

System

Motion/OCB or Empty

EHV 1-2

Empty

Event 4

Event 5

System

Motion/OCB or Empty

EHV 1-2

Empty

Empty

Event 5

System

Motion/OCB or Empty

EHV 1-2

EHV 3-4

Event 4

Event 5

System

Motion/OCB or Empty

EHV 1-2

EHV 3-4

EHV 5-6

Event 5

System

«
...
59
60
61
62
63
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов