doble TDR9000 Скачать руководство пользователя страница 345 | Manualshive

Страница: 345 / 454

doble TDR9000 Скачать руководство пользователя страница 345

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

B-17

Monday

, November 26, 2001 1:09 pm

Figure B.13 D8 and D14 LEDs

• With the exception of D8 and D14, if any LED shown in

Figure B.11 on page B-15 is Off or Red after the startup sequence,
that circuit board has experienced a startup problem.

• After the startup sequence, the communications loopback LED

should illuminate. This LED is viewed by looking through the
handle/vent opening (nearest the System module) on an angle
from the back of the Instrument to the front. There are three LEDs
visible. The loopback LED is on the bottom. If the LED:
• Illuminates after instrument startup completes, serial commu-

nications are working up to the front panel connector.

• Does not illuminate, check the CPU, the internal W6 ribbon

cable, and the System module communications circuits.

D8 and

D14 LEDs

Live AC

on Leads

«
...
343
344
345
346
347
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов