manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 440 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 440

Universal Adapter

I-30

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

These low sense voltages make good connections a necessity. All places 
to which the Contact Cables are to be attached must be free of paint or 
corrosion. Wire brushing the point of connection is advisable. 
Connections to a hinge pin or similar device must be avoided. The 
crocodile clip grip should not be loose or wobbly. The weight of the 
suspended cables must not be supported by the crocodile clips; the 
contact cable should be draped around a fixed object which supports the 
weight of the cable.

On circuit breakers that have a very violent mechanical operation, a 
clamp type connection may be warranted. The crocodile clip is bolted to 
a metal tab at the cables’ end and can be removed to facilitate adding 
another type of connector to the cables’ end.

Table I.3 lists the voltages used for EHV and OCB channels for the 
TDR9000.

AN11: Sampling Rates

The basic concept for digital sampling is that the sampling rate should be 
faster than the event that being captured. This sample rate captures the 
event. However, if there is a need to determine the actual length of the 
event, within 10%, then the sampling rate must be an order of magnitude 
faster than the event. To detect and determine the length of bounces of 1 
msec, with an accuracy of 10%, a sampling rate of 10 kHz (a sample 
every 100 

µ

sec) is necessary.

Sampling rates are a prime consideration in the resolution of motion and 
velocity. Slower sample rates affect measurements that involve a contact 
event and motion subsequent to that contact event. Measurement of 
Contact Wipe can be affected by slow sample rates.

Instantaneous velocity measurements from digital travel transducers are 
also affected by the sample rate.

Table I.3  TDR9000

™

 Contact Sensing Voltages

Low 

Ω

High 

Ω

None

TDR9000

EHV

7.5V

15V

15V

OCB

15V

48V

15V

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов