manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 35 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 35

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

1-9

Monday

, November 26, 2001 1:09 pm

TDR9000

™

 

Connections: 
First Trip/Close 
Test

Table 1.3 and Table 1.4 list the connections to the TDR9000 required for 
both a minimum set of channels and the recommended set of channels, 
respectively. Since this is an external trigger test, no control cable is used. 

*Connect to an Event module if using the Aux Contact trigger source, and 
to the Trigger In connectors on the System module if using the Trigger In 
source. 

Table 1.3 applies to a TDR9000 with one Event module.

Table 1.3  TDR9000

™

 Using a Minimum Set of Channels

Item

Signal

Type

TDR9000 Module 
Connection

1

Main Contact 
(from CT secondary)

Analog

Event

2

Trip relay coil 
current

Analog

Event

3

DC Supply voltage

Analog

Event

4

52CS/T contact state
(for Trigger In source)

Auxiliary Contact Event or Trigger In*

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов