manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 235 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 235

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

A-35

Monday

, November 26, 2001 1:09 pm

Device Timing 
Parameters

These parameters apply to the tests overall. Restrictions are discussed 
individually.

Delay Length:

Delay Length and Delay 1 Length/Delay 2 Length

Delay Length is the length of time after the 
inception of running a test before the test 
condition, for example a trip pulse, is 
implemented.

Delay 1 Length sets the time for a first test 
condition to be implemented.

Delay 2 Length sets the time, for those tests where 
it is applicable, such as an O-C-O test, for a second 
test condition to be applied.

Each of these choices activate the Trip, Close, and 
Delay 1 and 2 fields as listed in Table A.1.

Table A.1  Delay Command Parameters

Test Type

Command Parameters

Reclose (O-C)

Standing

Trip Command

Delay

Trip Command
Delay 1 (Close Command)

Trip Free (C-O)

Standing

Close Command

Delay

Close Command
Delay 1 (Trip Command)

Contact 1 Make

Close Command

O-C-O

Standing

Trip Command
Close Command
Delay 2 (Trip Command)

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов