manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 438 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 438

Universal Adapter

I-28

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

Open the close circuit knife blades and add the two clip-to-clip jumpers 
as shown in Figure I.23 on page I-27. With the connection of the Close 
initiate leads as shown, and the two additional clip-to-clip jumpers, the 
test set now monitors and measures the current that flows in the closing 
circuit without disabling any fusing or anti-pump protection.

The Close pulse length should be lengthened from the default value of 
133.3 ms to approximately 300 ms to allow the close coil current to be 
interrupted by the 

X

 relay contacts. This is done in the Command 

Parameter portion of the Breaker Test Plan. If the same circuit is 
employed for Trip-free, Reclose, or O-C-O tests, then their close pulses 
should be lengthened accordingly.

The time from Close coil energization to Main Contact closure is 
determined using the graphical results. The time from test initiation 
(

X

relay energization) to Main Contact operation is tabulated and given in 

the Test Results Report.

AN8: Simultaneous Energization of Two Sets of Trip Coils 
in a Single Circuit Breaker 

Many modern high voltage circuit breakers have two sets of trip coils that 
may have independent sources of power. To energize both sets of trip 
coils simultaneously from their respective power sources, without 
electrically tying the battery banks together, proceed as follows:

1.

Connect the pair of trip leads to energize Trip Coil #1 and connect the 
pair of close leads to energize Trip Coil #2. On the Breaker Test Plan, 
Command Parameters, Trip-Free Parameters, select a Trip-Free Delay 
of 0.0 msec.

2.

Close the circuit breaker. When the Trip-Free test is initiated, both the 
Trip and the Close circuits are energized simultaneously.

3.

The Trip current for Trip Coil #1 is displayed as Trip Current on the 
Breaker Performance Report and on the graphical results. Likewise, 
the Trip Current for Trip Coil #2 is displayed as Close Current on the 
Breaker Performance Report and on the graphical results.

If the circuit breaker opens, it has passed the test. 

N

OTE

The Close Circuit current maximum range is 20 A. 

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов