manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 187 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 187

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

4-89

Monday

, November 26, 2001 1:09 pm

To do so:

1.

Right-click either the 

Graphics

 or 

Overlay Graphics

 tab to access to 

the 

Properties

 window. 

If the 

Automatically Overlay Signals With The Same Name

 box:

• Is checked, channels with the same name, such as all Main 

Contact channels, are automatically overlaid. 

• Is not checked, all overlays must be performed manually. 

2.

Point to the 

Drag and Drop

 icon to the right of a signal.

3.

Click and hold the mouse button.

4.

Move the mouse until it is over the target channel and the 

Overlay 

icon appears.

5.

Release the mouse button. 

The two channels are now overlaid in the same channel frame. 
TRXField automatically selects different colors for each (”Channel 
Viewing Properties” on page 4-92).

6.

To overlay more channels, Repeat steps 1 through 5.

• When moving a channel:

• If  the 

Re-order

 icon appears, the user is re-ordering, not over-

laying, the channels.

• If  the 

Overlay

 icon is displayed, channels are overlaid.

• To restore all Test Results, select the

 Reload Original

 button.

Re-order

Displayed

Channels

Test Results can contain many channels. To remove unwanted channels:

• Click the

 X

 next to channels.

This deletes the channels from the display only, not from the Test 
Results. Moving the channels up or down on the screen can make 
it easier to compare them.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов