doble TDR9000 Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 454

doble TDR9000 Скачать руководство пользователя страница 248

Test Plan Items

A-48

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

The delay value is calculated as follows:

The default values are:

Figure A.57 shows how the O-C-O with a Standing Delay works.

Figure A.57 O-C-O Delay Operation

Delay

A trip command of a specified duration is applied to the circuit breaker
at time zero (Figure A.58). A close command of a specified duration is
applied to the circuit breaker delayed by a specified time interval
(Delay 1 Length) after the initiation of the trip command. The second trip
command is applied to the circuit breaker that is delayed by a specified
time interval (Delay 2 Length) after the initiation of the close command,
and is left on for the remainder of the test.

Figure A.58 Reclose Trip Delay

For 60 Hz

Delay > 55 ms + (Trip pulse – 8.3 ms)

For 50 Hz

Delay > 55 ms + (Trip pulse – 10 ms)

60 Hz

50 Hz

Trip Pulse

66.6 ms

80 ms

Close Pulse

133.3 ms

160 ms

Delay

55 ms + (66.6 ms – 8.3 ms) = 113.3ms 55 ms + (80 ms – 10 ms) = 125 ms

delay

Trip Command

Close Command

«
...
246
247
248
249
250
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов