doble TDR9000 Скачать руководство пользователя страница 334 | Manualshive

Страница: 334 / 454

doble TDR9000 Скачать руководство пользователя страница 334

Self-Diagnostics Test

B-6

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

If no failures are detected, the test ends with the

Global Self Test

complete. If a failure is detected, the software moves on to the

Local Self

Test

(Figure B.5). An alarm sounds and, as with the

Global Self Test

, the

Safety Switch must be pressed within 60 seconds.

Figure B.5 Local Self Test

6.

Press the Safety Switch until the alarm ceases.

Once this second part of the test begins, the window appears as
shown in Figure B.6. A status bar appears as the TDR9000 collects
data about the validity of source signals sent through the sensing
cards, the cards responsible for signal processing for all test types
during normal operation. This test requires several minutes to
complete, and is longer for fully populated Instruments.

«
...
332
333
334
335
336
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов