doble TDR9000 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 454

doble TDR9000 Скачать руководство пользователя страница 145

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-47

Monday

, November 26, 2001 1:09 pm

Items that Effect

Individual Motion

Channels

The following items are configurable.

In use

A checkbox that activates or deactivates the
associated channel.

Travel Label

A field for entering the travel name associated with
the channel.

Velocity Label

A field for entering the velocity name associated
with the channel.

Phase

A scrollable picklist for selecting the phase
associated with the channel.

Items that Effect

Overall Motion

Channel Behavior

The motion channels are split into two groups:

• Motion Channels 1-3
• Motion Channels 4-6

The selections described below apply to these groups.

Transducer Type

A picklist for choosing the transducer type:

•

Linear

• Rotary

N

OTE

Selecting Rotary changes the Transfer Function field to reflect degree
measurement.

Transducer Unit

A picklist for choosing the transducer unit of
measurement:

• English
• Metric
• Degrees

(dictated by

Transducer Type

)

Transfer Function

Two user-entered fields for entering the data used
to translate the travel of the contacts into a useful
indication of transducer travel. For an in depth
explanation of this topic, refer to ”Transfer
Function” on page A-58.

A

Motion Connector

window is available for each configured motion

channel. This window configures only items specific to an individual
motion channel.

«
...
143
144
145
146
147
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов