doble TDR9000 Скачать руководство пользователя страница 121

Страница: 121 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-23

Monday

, November 26, 2001 1:09 pm

The Rotary Adapter, shown in Figure 4.10, provides two different
functions:

• When mounted in the ROTARY position, the adapter toggles a

micro-switch that indicates to the Instrument that a rotary
measurement is being performed.

• When mounted in the ROTARY position, it covers the gate area,

which serves as a reminder that it must be removed prior to
inserting the travel rod to perform a linear measurement.

OTE

If the Rotary Chuck requires tightening, tighten while using the locking
pin to hold the Rotary Shaft in place.

To tighten the Rotary Chuck:

Press on the locking pin while rotating the Rotary Chuck. The locking
pin drops into a slot in the Rotary Shaft and holds the Rotary Shaft in
place.

Insert the Chuck Key into the Rotary Chuck and tap it with a light
object until the Rotary Chuck rotates clockwise.

Figure 4.10 Rotary Adapter

Chuck Key

Locking Pin

Rotary

Captive Screw

Captive

Chuck

Screw

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 121 / 454

Результаты поиска

Содержание TDR9000

Отзывы: