manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 4 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 4

Some states do not allow the exclusion of implied warranties, so the 
above exclusion may not apply. This warranty gives the purchaser 
specific legal rights and the purchaser may also have other rights which 
vary from state to state.

DOBLE warrants the disks on which the software product is furnished to 
be free from defects in materials and workmanship under normal use for 
a period of one hundred and twenty (120) days from the date of shipment 
from DOBLE.

Limitations of 
Remedies

DOBLE’s entire liability and Purchaser’s exclusive remedy shall be:

1.

the replacement of any disks not meeting doble’s “limited warranty” 
which are returned to doble.

2.

If DOBLE is unable to deliver replacement disks which are free from 
defects in materials and workmanship, Purchaser may terminate this 
agreement. By returning the software product and all copies thereof 
in any form and affirming compliance with this requirement in 
writing, DOBLE will refund the purchase price.

IN NO EVENT WILL DOBLE BE LIABLE TO PURCHASER FOR ANY 
DAMAGES, INCLUDING ANY LOST PROFITS, LOST SAVINGS OR 
OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT 
OF THE USE OR INABILITY TO USE SUCH SOFTWARE PRODUCT, 
EVEN IF DOBLE OR AN AUTHORIZED DEALER HAS BEEN ADVISED 
OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY 
ANY OTHER PARTY.

Some states do not allow the limitation or exclusion of liability for 
incidental or consequential damages, so the above limitation or 
exclusion may not apply.

For Equipment Maintenance, contact:

Customer Service Manager 
Doble Engineering Company
85 Walnut Street
Watertown, MA 02472 (USA)

Telephone: 617-923-2921
FAX: 617-926-0528
Email: [email protected]
Web: www.doble.com

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов