doble TDR9000 Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 454

doble TDR9000 Скачать руководство пользователя страница 158

Configuring Test Plans

4-60

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

N

OTE

For the Slow Close test the following parameters are available:
Recording Length, Time Display, and Timing Events as listed in
Table 4.4.

The Trip parameters identified in Figure 4.37 on page 4-59 are defined as
follows:

A

A

Trip Command

graph that displays the Trip

waveform produced by the present test parameters.

B

A

Close Command

graph that displays the Close

waveform produced by the present test parameters.

C

A measurement scale with dimensions that toggles
between cycles or msecs.

D

Radio buttons for displaying measurements in time
or in cycles.

E

A

Trip Command

field where the Trip duration is

input or changed. This is then displayed in item A.

F

A

Close Command

field where the Close duration

is input or changed. This is then displayed in
item B.

G

Two delay fields,

Delay 1

and

Delay 2

, where the

Trip or Close command test delays are input or
changed.

H

A series of fields that configure the test timing
functions for Close only. These fields are activated
when Close is selected as the test type. Selections
made on this list activate the

Timing Event

picklist

and the

Timing

Trigger

and

Timing

Channel

picklists as listed in Table 4.4.

Timing Trigger and Timing Channel depend on the
timing event selected.

The

Timing

Channel

picklist displays all configured

channels and sets the channel where recording is
performed.

«
...
156
157
158
159
160
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов