doble TDR9000 Скачать руководство пользователя страница 229 | Manualshive

Страница: 229 / 454

doble TDR9000 Скачать руководство пользователя страница 229

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-29

Monday

, November 26, 2001 1:09 pm

General Test Plan
Functionality

The two areas of functionality used to configure the TRXField Test Plan
are the:

• TRXField menu bar
• Right-click menu

TRXField

™

Menu Bar

The TRXField menu bar is shown in Figure A.31.

Figure A.31 TRXField

™

Menu Bar

The menu items include:

File

• New Test Plan

A blank Library test Plan appears.

• Open

An Open window appears from which existing Test Plans or
Test Results are opened. Refer to ”Tab Navigation” on page 3-5
for more information.

• Save

A Specify File Type dialog box appears and a TDR9000 file or
TR3000 file is created. Refer to ”Saving Test Results/Test Plans”
on page 4-95 for more information.

• Overlay Graphics

A dialog box appears where the Graphics tabs for Test Result files
of similar type can be overlaid. This item is only active when a
Test Result file is open. Refer to the TRX User’s Guide for more
information.

• Print

Refer to ”Printing Test Results” on page 4-100 for more
information.

• Exit

«
...
227
228
229
230
231
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов