doble TDR9000 Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 454

doble TDR9000 Скачать руководство пользователя страница 249

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-49

Monday

, November 26, 2001 1:09 pm

The Instrument does not impose any special restrictions on Delay 1
Length, however, the following formula is useful:

Delay 1 Length < 55 ms + Trip Pulse

The default value is:

55 ms

The Delay 2 Length can be calculated as follows:

Delay 2 Length > 55 ms + (Trip pulse – Delay 1 Length)

The default value is:

Delay 2 Length = 55 ms + (66.6 ms – 55 ms) = 66.6 ms

Figure A.59 shows how the O-C-O Delay works.

Figure A.59 Reclose Trip Delay Operation

Contact 1 Make

A trip command of a specified duration is applied to the circuit breaker at
time zero (Figure A.60). A close command of a specified duration is
applied to the circuit breaker delayed by a specified time (delay) after the
initiation of the trip command. The second trip command is initiated
when electrical closure is first detected on the Main Contact channel #1
(usually connected to contact #1 in Phase A) and is left on for the
duration of the test.

Figure A.60 O-C-O Contact 1 Make

delay2

delay 1

Trip Command

Close Command

«
...
247
248
249
250
251
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов